Dyson is known for its vacuum cleaners, but recently it has been getting more into wet hard-floor cleaners. Its first attempt launched in August 2024, and you can read all about it in my Dyson WashG1 review. Now there’s a new model on the block: the Dyson Clean+Wash Hygiene.
Unlike the best wet-and-dry vacuums on the market, neither use suction, but instead harness a combination of hydration, agitation and separation to clean your hard floors. To put it another way, they add water, dislodge dirt using cleverly designed rollers, and then separate solid and liquid waste for easy disposal.
1. It’s fiddly and messy to empty
The WashG1 has its dirty-water tank mounted to its handle, and this is easy to remove and empty. The solid waste tray slots into the floorhead, and is slightly more complex to fit, but still fairly straightforward.
In contrast, the Clean+Wash Hygiene has its dirty-water tank mounted into the top of the floorhead, with a two-part solid waste tray integrated in. Separating the three components is fiddly, and putting it back together again even more so – and I say this as someone who’s pretty good at jigsaws.
The knock-on effect of having a more complicated floorhead, with lots of connecting components, is that it’s a lot leakier than the nice, simple WashG1. Now, all the wet floor cleaners I’ve used are a little bit drippy – it feels like an unavoidable problem – but the Clean+Wash Hygiene seems especially bad. It felt like every time I went to empty the dirty-water tank something would dribble out onto me or the floor.
2. There’s only one roller
The WashG1’s floorhead has two large microfiber rollers and a bristled roller for solid messes, and delivers efficient cleaning. In contrast, the Clean+Wash Hygiene only has space for one roller on its more complicated floorhead.
I will say I do prefer the microfiber roller design on the Clean+Wash. The scrubbing action is slightly improved, thanks to the addition of wiry, longer fibers that extend a bit from the roller. My ideal scenario? The upgraded microfiber roller design, mounted in the old floorhead.
3. The water tanks are too small
The WashG1 has a 1L clean-water tank, and a 0.8L dirty tank, whereas the Clean+Wash Hygiene equivalents are 0.75L and 0.52L respectively, and the difference was noticeable on test; not so much during the actual mopping – Dyson has tweaked the water delivery so there’s only a fine sheen of liquid applied to floors, eking out the clean water as much as possible – but during the self-clean cycle.
Each self-clean cycle uses more than half a tank of clean water, which means for the first few times I ran one of these I had to stop twice per cycle: once to refill the clean water tank and again to empty the dirty tank. Eventually I learned to do this before each self-clean cycle to avoid annoying interruptions.
The benefit of smaller tanks is a more streamlined and lighter machine, so I can see why Dyson was keen to keep things compact here – you’ll need to decide your priorities when making your choice.
4. Cleaning the dirty-water tank is tricky
One of the things I liked about the design of the dirty-water tank on the WashG1 – and something Dyson highlighted as a big benefit when I was first shown that machine – was that the waste water tank was designed to be easy to clean.
It’s wide enough that you can get your hand in and wipe everything out, and there are no awkward corners where grime can collect. I’ve tested a number of wet-dry vacuums now, and I’ve never seen anything like it – dirty water tanks are always too small to get your hand in, and always have sharp edges that get grubby almost instantly.
The setup on the Clean+Wash is especially bad, though. It opens with a screw cap, and there’s no access to the inside at all. It’s not the worst thing for a dirty water tank to be dirty, but this feels like an oversight in terms of long-term maintenance.
Dyson WashG1 vs Clean+Wash Hygiene: specs compared
| Header Cell – Column 0 |
Dyson WashG1 |
Dyson Clean+Wash Hygiene |
|---|---|---|
|
Cleaner size (H x L x W): |
44.9 x 8.9 x 11.8 in / 114 x 22.5 x 30cm |
43.1 x 9.6 x 11 in / 109.6 x 24.4 x 28cm |
|
Dock size (H x L x W): |
9.4 x 9.4 x 11.8 in / 24 x 24 x 30cm |
9.4 x 11 x 10.1 in / 24 x 28 x 25.7cm |
|
Weight (empty): |
10.8 lbs / 4.9kg |
8.4 lbs / 3.8kg |
|
Clean water tank volume: |
1L |
0.75L |
|
Dirty water tank volume: |
0.8L |
0.52L |
|
Max runtime: |
35 mins |
45 mins |
|
Dock cable length: |
3.9ft / 1.2m |
5.9ft / 1.8m |
Follow TechRadar on Google News and add us as a preferred source to get our expert news, reviews, and opinion in your feeds. Make sure to click the Follow button!
And of course, you can also follow TechRadar on YouTube and TikTok for news, reviews, unboxings in video form, and get regular updates from us on WhatsApp too.
